Oudmaarnogvliegen

Best simmers Due to lack of capabilities in making a flight plan in MSFS2020, I plan to use an external flight planner. I have my preference for SkyVector. It is free and it is recommended by the writers of A Glide to Fligtsimulator, from SoFly. Now I read there that SkyVector is integrated into Flightsimulator. But how then you should be able to open SkiyVector in Flightsim anyway? If I'm going to make a flight plan in FLSim, I have to see it in SkyVector, so I can add the desired waypoints and if I fly, I'll see my plane in SkyVector. I had already created an account with SkyVector, but I do need to. According to the writers of A Glide to Fligtsimulator apparently not, because that is not mentioned by them. Who can tell me more about it? But pleace, no reference to YouTube. Then it goes way too fast. As a Dutchman I translate my text into English with the help of the MS translator and vice versa. It's hard to follow spoken language. That's the reason. Thank in advance, Bert

The problem I had with the flight plan has been resolved. We found the solution at FlightSimulator forum. If you are still interested in the solution then click on the following link: https://forums.flightsimulator.com/t/problem-with-flight-plan-bug-and-autopilot/228003. Greeting Bert

I've been experimenting with your data a little bit. In addition, I discovered that if I choose a Direct route to an airport in the menu, that route will be seen by the AP with Nav as a choice. But if I choose a flight plan with the setting: AP Nav (in the rose of the compass is GPS) then that is not recognized or seen by the AP but my plane goes directly to the North Pole. The first part of the quickplan route is magenta and it remains that. The Nav arrow frequencies don't change my flight plan can be seen in PMD either, but I don't see any change there either. The 'hook' stays at the first 2 waypoint. Surely the AP should receive route info from the waypoints that will point the needle of the rose in the right direction? The needle stands and continues to point north.

U bedoelt hier toch niet de handleiding van de fysieke uitvoering van de G1000? Kunt u mij een link sturen waar ik die kan vinden? Dan ga ik die handleiding eerst maar een bestudeer. Ik ben met uw gegevens een beetje aan het experimenteren geweest. Daar bij ontdekte ik dat als ik in het menu een Directe route naar een vliegveld kies dat dan die route wel gevolgd wordt door de AP met Nav als keuze. Maar als ik kies voor een vluchtplan met dezelfde instelling: AP Nav dan wordt dat niet gezien door de AP maar gaat mijn vliegtuig rechtstreeks naar de Noordpool. Ik heb in het verleden met FSX gevlogen daar was het vliegen op een vluchtplan super eenvoudig. Maakte een vliegplan kies voor GS en Nav en hup daar ging het keurig op het routelijntje

Thanks for the effort but it didn't work.

Let me explain the situation: I've put up a flight plan for my Cessna C172 Skyhaw and than I take off. I have choosen High Altitude under the aircraft selection. I can manoeuvre my Cessna. When I'm at the given altitude, I turn on AP first with hdg for the first part of my plotted flight route, so fly on the compass. So far everything is going well. The foregoing part is intended as a test for the control capacity of the control. So normally I would immediately opt for AP Nav Now I switch over to AP Nav. My Cessna starts turning directly north while my flight plan route is south. If I let it take its course, it'll go exactly to 360 degrees. The first part of my route, until the next waypont, is active (red). While testing, I'm going back to AP hdg, where my Cessna is nicely following the plotted compass route, until I'm past the first waypoint. After that, the first part of the route remains red and also remains red (active) after each waypoint passage. I don't see any changes in nav radio frequency after passing a waypoint. This might make sense since I am flying AP hdg. But when flying with AP nav, I can't test that because I just don't pass a waypoint. Also, my NavLog table is dead. I mean there is no change whatsoever. When I click the FPL soft button in the Garmin G1000 display, I also see the flight plan so it must be loaded.. right? Again, I don’t see any change towards the next waypoint. Changing planes, flying plans doesn't help either. I've been looking for a solution for this problem since I bought this FS2020 months ago. Do I do something wrong or forget something. Who can help me? Appperature: DELL Computer Name: Desktop-I7QPR8E Processor: Intel® Core ™i7 10700F CPU@ 2.90GHz RAM: 16GB System type: 64-bit operating system, 64 bit-procssor OS: WINDOWS 10 Home Control hardware: Combination Saitek ProFight Yoke system and Throttle Chosen app: MSFS 2020