Stewie Posted January 26, 2021 Share Posted January 26, 2021 A picture of this dilemma has been attached. I'm hoping that there is a fellow FS2004 Simmer that has had this issue and was able to successfully resolve it. Unfortunately, I've searched google and found others that have experienced this issue, but no solution. Also, Aerosoft Forum has yielded no support. I have uninstalled and reinstalled the software, as well as, adjusting the scenery level to no avail. Not sure what else to do. Any support is greatly appreciated! Stewie Link to comment Share on other sites More sharing options...
Dedl Posted January 26, 2021 Share Posted January 26, 2021 Hi Stewie, to get FS2004 support from AS is like wanting homegrown strawberries in wintertime. Have you tried to set an exclude rectangle in this aerea in the AFCAD/ADE-file with Airport Design Editor? Dedl Link to comment Share on other sites More sharing options...
Roger Wensley Posted January 26, 2021 Share Posted January 26, 2021 Stewie, give me the exact position in degrees and minutes etc, the width of the runway asphalt, and the airport elevation in feet or metres. rogwen at rogers dot com Link to comment Share on other sites More sharing options...
Stewie Posted January 26, 2021 Author Share Posted January 26, 2021 Stewie, give me the exact position in degrees and minutes etc, the width of the runway asphalt, and the airport elevation in feet or metres. rogwen at rogers dot com Roger - Thank you so much for assisting. Here's the information requested...I hope. Exact Position - Using Afcad it shows N47*27.4917' E8*32.8800' 333.3* (same as the Airport Reference Point) Runway - Reciprocal End 34 Base End 16 Surface - Concrete Width 262 Length 12287 Pattern Alt 5000.0 Elevation 1416.0 Is it possible if I move the Airport Reference Point that would move the house? Link to comment Share on other sites More sharing options...
Stewie Posted January 26, 2021 Author Share Posted January 26, 2021 Hi Stewie, to get FS2004 support from AS is like wanting homegrown strawberries in wintertime. Have you tried to set an exclude rectangle in this aerea in the AFCAD/ADE-file with Airport Design Editor? Dedl Dedl - Thank you for responding. Not sure how to use ADE. I have discovered though, that the house sits at the exact location as the Airport Reference Point. Not sure if I move the reference point on the Afcad if that would move the house. Link to comment Share on other sites More sharing options...
Stewie Posted January 26, 2021 Author Share Posted January 26, 2021 Roger - Thank you so much for assisting. Here's the information requested...I hope. Exact Position - Using Afcad it shows N47*27.4917' E8*32.8800' 333.3* (same as the Airport Reference Point) Runway - Reciprocal End 34 Base End 16 Surface - Concrete Width 262 Length 12287 Pattern Alt 5000.0 Elevation 1416.0[ATTACH=CONFIG]224982[/ATTACH] Is it possible if I move the Airport Reference Point that would move the house?[/QUOT FYI - Moving the reference point did not make a difference. However, the other thing I noticed is while the runway is Concrete, the center of it is Asphalt. Is that normal? Is it possible that there is a conflict that causing that? Grasping at straws. Link to comment Share on other sites More sharing options...
Roger Wensley Posted January 26, 2021 Share Posted January 26, 2021 Stewie, I need your email address so I can send you an exclude bgl that you will use, so just email me at the address I gave above so I can reply. Link to comment Share on other sites More sharing options...
tgibson_new Posted January 26, 2021 Share Posted January 26, 2021 Re: concrete vs asphalt - all that does is make the connections to asphalt taxiways a little cleaner, nothing else. Tom Gibson CalClassic Propliner Page: http://www.calclassic.com Link to comment Share on other sites More sharing options...
Stewie Posted January 26, 2021 Author Share Posted January 26, 2021 Stewie, I need your email address so I can send you an exclude bgl that you will use, so just email me at the address I gave above so I can reply. Roger - Sent a PM. Couldn't figure out how to get the email address. Thanks a million for doing this for me. Link to comment Share on other sites More sharing options...
Stewie Posted January 26, 2021 Author Share Posted January 26, 2021 Thanks Tom! Truly appreciate you my friend. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now