connolly44

confusing.

 

you said there were only a few lights.

Now you list a whole bunch.

Nevermind.

 

But there are only a few lights (the same amount as in most default aircraft). The other [lights] are things like Afterburners and Contrails which all work perfectly.

I am getting a bit confused here.

This is now my [Lights] coordinates in aircraft.cfg :

[lights]

//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing

light.0=4, 78.50, 1.35, 5.00, fx_shockwave_vclight_l ,

light.1=4, 78.50, -1.35, 5.00, fx_shockwave_vclight_l ,

light.2=9, -55, -19.0, -3.5, fx_GA_CONCORDE_AFTERBURNER

light.3=9, -55, -15.0, -3.5, fx_GA_CONCORDE_AFTERBURNER

light.4=9, -55, 16.2, -3.5, fx_GA_CONCORDE_AFTERBURNER

light.5=9, -55, 20.2, -3.5, fx_GA_CONCORDE_AFTERBURNER

light.6=7, -60.0, -19.0, -2.0, fx_contrail_s

light.7=7, -60.0, -15.0, -2.0, fx_contrail_s

light.8=7, -60.0, 15.8, -2.0, fx_contrail_s

light.9=7, -60.0, 19.8, -2.0, fx_contrail_s

light.10=2, -39.0, -38.0, -2.30, fx_shockwave_strobe_2 ,

light.11=2, -39.0, 38.0, -2.30, fx_shockwave_strobe_2 ,

light.12=3, -34.9, -35.0, -2.30, fx_shockwave_navred ,

light.13=3, -34.9, 35.0, -2.30, fx_shockwave_navgre ,

light.14=2, -101.95, 0, 7.45, fx_shockwave_beaconh_l ,

light.15=10,-10, 0, -3.5, fx_GALConcordeFOG,

light.16=10,-10, 0, -3.5, fx_GARConcordeFOG,

light.17=8, 80, 0, 0, fx_RCB_machenvlop ,

light.18=5, 44.0, 0.0, -6.0, fx_Shockwave_landing_light , //Shockwave light

and I have now tried changing the landing light to nose gear in panel [Vcockpit01].

gauge04=shockwave_lights!SW Lights_gear, 1,1,1,1 //shockwave light

Every light from light.0 to light.17 works perfectly but no light.18 no matter where I place it???

These are the only other lights in the [lights] section

light.10=2, -39.0, -38.0, -2.30, fx_shockwave_strobe_2 ,

light.11=2, -39.0, 38.0, -2.30, fx_shockwave_strobe_2 ,

light.12=3, -34.9, -35.0, -2.30, fx_shockwave_navred ,

light.13=3, -34.9, 35.0, -2.30, fx_shockwave_navgre ,

light.14=2, -101.95, 0, 7.45, fx_shockwave_beaconh_l ,

There are three landing lights which are controlled from the aircraft panel but I assume they are from the Model File? As they are not shown in the aircraft.cfg file?

Hello all

On Concorde X (Arrow Air version) I cannot get any Shockwave landing lights to work?

I have copiied and pasted from the manual to [Vcockpit01] the following:

gauge04=shockwave_lights!SW Lights, 1,1,1,1 //shockwave light

I have also copied and pasted the following into the aircraft.cfg [Lights] section as follows:

light.18=5, 43.420, 7.50, 0.370, fx_Shockwave_landing_light , //Shockwave light

light.19=5, 43.420, -7.50, 0.370, fx_Shockwave_landing_light , //Shockwave light

I even used a position close to the aircrafts existing Landing lights. I was hoping to make the shockwave's into taxi lights as there are no taxi lights with this aircraft!!

Kind regards

Hello Brian

Thank you so much for your reply.

I never even saw this version during my searches, but maybe that is because I only put V-22 instead of V-22B into the search box!!

I will now make this V-22B into a Mach 1 version. I know how to do this.

Many thanks once again

Frank

Hello folks

I have FSX Steam and fly mainly one aircraft, an add-on (FS2004) Bell-Boeing V22 Mach 1 (I like getting to places reletively fast)

However, this aircraft has blank outside views. I just see the scenery all around me.

Is there any way that I can add, for example, the edges of the panel when my joystick hat switch is pushed forward right and forward left?

Many thanks

Hello all

I have sorted out the aircraft rolling problem by adjusting the figures in the [Weight and Balance] section of the aircraft.cfg file as follows:

empty_weight =60000.000000

empty_weight_roll_MOI =1500000.000000

empty_weight_pitch_MOI =3000000.000000

empty_weight_yaw_MOI =2000000.000000

empty_weight_coupled_MOI =0.000000

max_gross_weight =90000.000000

I have sped up my default B737-800 by using a faster .air file and adjusting several parameters in the aircraft.cfg file.

However, this has caused the aircraft to sway (roll) from side to side, even though it still holds the set autopilot heading.

How can I stop this gradual rolling from side to side? Have I a wrong parameter(s) in my aircraft.cfg file?

Many thanks

I seem to have sorted it out.

Instead of using the Auto start key, I changed the Button to "Starter All (on/off)." Press this once then turn on the four individual Engine Control Switches on the B747 Throttle Quadrant.

Many thanks for your input

Frank

Thank you for your advice.

I do use the Automatic startup command and also N1 and N2 do spin up correctly.

However, I will try a different Throttle Quadrant and see if that rectifies the situation

I fly the four engine Bae146-100 and it takes a month of Sunday's to fire up the engines (I use the default B747 Throttle Quadrant).

I have tried several different sound sets but always the same long delay.

Is there any parameter within the aircraft.cfg (or another file) which will shorten the startup time?

Many thanks

Frank

Hello

I have done it by a lot of trial and error!!!

Changed the Default View at the bottom of the Panel.cfg file to SIZE_Y=6143

Thank you for your interest

Frank

//Antonov Panel

[Window Titles]

Window00=Main Panel

Window01=Talal's Map View

window02=Flypad

[VIEWS]

VIEW_FORWARD_WINDOWS=MAIN_PANEL,GPS_PANEL,MINIPANEL,throttle_panel

VIEW_FORWARD_DIR=5.000, 0.000, 0.000

//--------------------------------------------------------

[Window00]

file=Main.bmp

size_mm=1280

window_size_ratio=1.000

position=7

visible=1

ident=0

window_size= 1.000, 1.000

window_pos= 0.000, 0.000

gauge01=Lear_45_XML!PFD, 512,533,250,425

gauge02=Lear_45_XML!yaw_indicator, 600,533,80,25

gauge03=Talal06!Talal's Map, 200,525,310,430

gauge04=IL96MT!EICAS Display_1, 980,533,250,250

gauge05=B737_800!ECU, 10,680,180,200

gauge06=Lear_45_XML!autopilot, 765,425,430,108

gauge07=Talal06!Icon_TM, 0,16,35,35

gauge08=Talal06!Talal-Control, 0,0,12,12

gauge09=FLPInfo!FLP_Info_2, 765,533,210,300

gauge10=Bendix_King_Radio!Bendix-King Radio Audio, 200,475,310,50

gauge11=Extra_XML!switch_panel, 40,400,320,75

gauge12=InfoGauge!InfoGauge, 530,400,250,35

gauge13=n_number_plaque!n_number_plaque, 595,914,80,25

gauge14=Rel_Wind_v3.0!RelWind, 610,440,60,80

gauge15=KingAir!beacon_light, 0,400,40,75

gauge16=KingAir!land_light, 360,400,40,75

gauge17=Flypad!Key_Comma, 0,0

gauge18=A109!109_annunciator_brake, 160,21,20,18

gauge19=KingAir_Radio!Com1, 0,475,100,110

gauge20=KingAir_Radio!Nav1, 100,475,100,110

gauge21=IL96MT!Autobrakes Switch, 68,894

gauge50=CALLOUT_SOUND!dsd_xml_sound3, 0,0,0,0, ./Sound/CALLOUT/Sound.ini

gauge51=CALLOUT!CALLOUT1000, 0,0,0,0

gauge52=CALLOUT!CALLOUT500, 0,0,0,0

gauge53=CALLOUT!CALLOUT400, 0,0,0,0

gauge54=CALLOUT!CALLOUT300, 0,0,0,0

gauge55=CALLOUT!CALLOUT200, 0,0,0,0

gauge56=CALLOUT!CALLOUT100, 0,0,0,0

gauge57=CALLOUT!CALLOUT50, 0,0,0,0

gauge58=CALLOUT!CALLOUT40, 0,0,0,0

gauge59=CALLOUT!CALLOUT30, 0,0,0,0

gauge60=CALLOUT!CALLOUT20, 0,0,0,0

gauge61=CALLOUT!CALLOUT10, 0,0,0,0

//--------------------------------------------------------

[Window01]

size_mm=400,420

window_size_ratio=1.000

position=8

visible=0

ident=7077

window_size= 0.960, 0.960

window_pos= 1.008, 0.025

gauge00=Talal06!Talal's Map, 0,0,400,400

//--------------------------------------------------------

[Window02]

Background_color=0,0,0,0

size_mm=465,685

window_size_ratio=1

visible=0

ident=1904 //Don't change this

position=3

nomenu=0

sizeable=1

no_luminous=0

window_size= 0.232,0.465

window_pos= 0.00, 0.050

gauge00=FlyPad!FlyPad, 0,0,0,0

//--------------------------------------------------------

[Default View]

X=0

Y=0

SIZE_X=8191

SIZE_Y=3035

Hello

Is there any way to remove the solid black rectangles which appear when using the hat-switch in the forward left and the forward right positions?

These rectangles seem to happen when using some (but not all) third party panels and are the same shape as a panel?

Many thanks

Frank

I think I may have resolved this.

The copy and paste from the [exits] section of aircraft.cfg file below.

I disabled the bottom line and the chocks have vanished?

[exits]

number_of_exits=4

exit_rate.0=0.15

exit_rate.1=0.15

exit_rate.2=0.15

exit_rate.3=0.15

//exit.1=0.05, -18.3, 7.8, -2.0, 1 //FSX Cars

I am not sure what you mean by pop-up panel?

Do you mean in the Panel.cfg file?

It is a freeware ATR72 by ISDT

I have an ATR72 which is nice to fly but the yellow Nosewheel Brake Chocks and a Rear Support Stand remain showing at all times including whilst in flight ?

How can I stop this please ?

Many thanks

This one

b7e7ling.zip

Hello folks

I have the following under [General]

[General]

atc_type=BOEING

atc_model=B787

editable=1

Hello

When using the radio and asking for Class D airspace transition, how does one get the aircraft type "B787 Dreamliner" included in the transmission. All I get is aircraft type "Boeing" ?

I am guessing the I have to place some sort of line/reference in the aircraft.cfg file ?