Jump to content

agnitfom2000

Registered Users
  • Posts

    34
  • Joined

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

agnitfom2000's Achievements

Expert  Simmer

Expert Simmer (3/7)

  • First Post Rare
  • Collaborator Rare
  • Week One Done
  • One Month Later
  • One Year In

Recent Badges

10

Reputation

  1. Actually meant ground idle thrust. Found some plots for the J-79 that at sea level showed about 490 lb. At 3 engines around 1,500 lb.; aircraft has a typical take-off weight of 80,000 lb. so at about 1.9%.
  2. Unfortunately, the aircraft I'm trying to model (the XB-68, essentially a 3 engine version of the B-58) is a historical paper study so it has very minimal information. The saving grace is that it does have a fairly common engine, the J-79. I'll try searching the flight manuals of some aircraft with this engine installed to try and find the flight idle thrust. I just got hold of the F-4J NATOPS so I will start there. From the experience with the G550, this behavior on the aircraft I'm modeling is at least plausible. My industry background is materials, structures, making high temperature components out of exotic alloys, and program management. I have much less experience on overall aircraft performance, so I really appreciate the assist from both of you.
  3. One of the things I see in FSX is that jet aircraft tend to accelerate on the runway even with the throttle at idle. The example I tested went from 0 to 54 knots on 13,000 feet of runway. Even more extreme than my old car with the idle screw set to the max! Everything in the model set-up was as realistic as possible. Drag scalars and the jet engine thrust scalar were all set to 1. My question for any jet pilots in this forum is whether this behavior is realistic, or is the jet engine performance model in FSX producing too much thrust at idle? If it is realistic, I'll leave things alone. If not, I'll do some experimenting to try and minimize the effect. Thanks David Allan
  4. Nicely done enhancement. Especially like the improved cockpit. Extra textures for an Australian version are great too.
  5. No flaps based on similarity to the B-58 delta wing, which has only elevons. The Concorde doesn't have flaps either. You are right about my missing the Engine 3 hydraulics. My mistake. About the engine, I suspect the issue is the thrust_scalar parameter - I had to set it to 1.35 to get the speed to Mach 2, which also gave too much thrust at idle. If I go back and retweak this would you be willing to try it out?
  6. Clicking on the following link will make it easier to find: https://a2asimulations.com/product-category/fsx/
  7. Are you referring to the badly twisted sky bridge or something else? I've also seen AI airliners at rest bouncing around on their landing gear spewing fire.
  8. Thanks for the kind comments! I really appreciate the support. As far as publishing the S-92, the floats were the last problem. Except for writing up the documentation and creating the package, everything is ready. I'm hoping to get it out within the next month. David PS: I'll try out the contact points too.
  9. I never thought about using lights to illustrate the different types of contact points. That's a great idea! David
  10. My condolences. I'm very sorry to hear that. I have really enjoyed his work. David
  11. I was out of town for a couple of weeks, but after returning I was able to make the floats work properly. See the picture: I ended up using Model Converter X to transform the model downwards about 1 1/2 feet. The animations also transformed properly. I did not adjust the float points or scrape points in the Aircraft.cfg. I did adjust the CG and landing gear contact points vertically. Here are the final results. I realize max feet/second speed is higher than realistic. [contact_points] 0.......1......2........3.....4......5...6.....7......8.....9....10....11..12...13...14..15.....16.. ;gear point.0=1, 12.7, 0.00, -4.50, 9500, 0, 0.5187, 75.0, 0.500, 1.2, 0.6, 5.0, 5.0, 0, 120.0, 200.0 point.1=1, -7.7, -5.20, -4.50, 9500, 1, 0.5187, 0.0, 0.500, 1.2, 0.6, 5.3, 5.3, 2, 120.0, 200.0 point.2=1, -7.7, 5.20, -4.50, 9500, 2, 0.5187, 0.0, 0.500, 1.2, 0.6, 5.3, 5.3, 3, 120.0, 200.0 ;bottom point.3=2, 18.50, -4.70, 2.70, 8000, 0, 0.0000, 0.0, 0.000, 0.0, 1.0, 0.0, 0.0, 4, 0.0, 0.0 point.4=2, 18.50, 4.70, 2.70, 8000, 0, 0.0000, 0.0, 0.000, 0.0, 1.0, 0.0, 0.0, 4, 0.0, 0.0 point.5=2, -9.600, -4.70, 2.70, 8000, 0, 0.0000, 0.0, 0.000, 0.0, 1.0, 0.0, 0.0, 4, 0.0, 0.0 point.6=2, -9.600, 4.70, 2.70, 8000, 0, 0.0000, 0.0, 0.000, 0.0, 1.0, 0.0, 0.0, 4, 0.0, 0.0 point.7=2, -2.000, -7.30, 2.70, 8000, 0, 0.0000, 0.0, 0.000, 0.0, 1.0, 0.0, 0.0, 4, 0.0, 0.0 point.8=2, -2.000, 7.30, 2.70, 8000, 0, 0.0000, 0.0, 0.000, 0.0, 1.0, 0.0, 0.0, 4, 0.0, 0.0 ;float point.9= 4, 8.50, -9.50, -0.50, 8000, 0, 0.0000, 0.0, 0.100, 1.5, 0.6, 0.0, 0.0, 4, 0.0, 0.0 point.10=4, 8.50, 9.50, -0.50, 8000, 0, 0.0000, 0.0, 0.100, 1.5, 0.6, 0.0, 0.0, 4, 0.0, 0.0 point.11=4, -5.60, -9.50, -0.50, 8000, 0, 0.0000, 0.0, 0.100, 1.5, 0.6, 0.0, 0.0, 4, 0.0, 0.0 point.12=4, -5.60, 9.50, -0.50, 8000, 0, 0.0000, 0.0, 0.100, 1.5, 0.6, 0.0, 0.0, 4, 0.0, 0.0 It worked OK for both FSX and P3Dv4. Thanks to everyone who helped out with this problem!
  12. I've had some partial success. It will float for any set of points where the Z value is less than -0.5 (-1, -2 etc. works). -1 did work, which was higher than the landing gear points. See picture below: Strangely enough, I had the exact same response when I took the model file and put it in the EH-101 directory and used those aircraft.cfg and .air files. I could only lower the aircraft so far before I got the crash again. I'm beginning to think the problem is the compiled model. Beean, I had put in ridiculously high values for the impact threshold to try and eliminate it as a cause. Looking at it again, I'm honestly not sure why it is different. Probably a silly typo. :confused:
  13. Thanks everyone for the responses. By the amphibious EH-101 I was referring to Carl Vokes' FSX Making The EH101 Helicopter Float. He provides contact points for the standard EH-101 provided with FSX. If you search flightsim.com, filter on FSX Helicopters, and search for the word float, his item comes up first in the search. I have tried out both suggestions, and even tried combining them. Unfortunately it still crashes at the same height between the bottom of the gear and the bottom of the fuselage. I've tried both opening up the simulation with the helicopter in a water landing area, and landing the helicopter on the water with the gear retracted. Even the really gentle landing from a 10 foot hover didn't work. It looked like it was working for a few seconds but then crashed. I'm thinking I have something else going on beyond the contact points, but I am not sure what.
×
×
  • Create New...