Search:

Type: Posts; User: tgibson_new

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Fs2004

    by tgibson_new
    Replies
    1
    Views
    155

    If you mean the Air Hauler program cannot find...

    If you mean the Air Hauler program cannot find your FS2004 installation, you can fix the registry entry by using the Flight1 Registry Repair Tool program.
    ...
  2. Replies
    5
    Views
    220

    Hi, They probably did that to allow AI...

    Hi,

    They probably did that to allow AI aircraft to take off from mid-runway?
  3. Replies
    1
    Views
    109

    It's happening to others: ...

    It's happening to others:

    http://calclassic.proboards.com/thread/9611/problem-saved-flights
  4. Replies
    8
    Views
    436

    My guess is that the True Airspeed gauge is...

    My guess is that the True Airspeed gauge is actually displaying -6, but the gauge programmer never thought about a plane moving backwards in the air mass and didn't program for it.
  5. Perhaps you have two of these sceneries installed...

    Perhaps you have two of these sceneries installed and one does not include textures?
  6. Take it apart and clean the contacts?

    Take it apart and clean the contacts?
  7. Replies
    2
    Views
    226

    AFAIK your only choice to change the size of a 2D...

    AFAIK your only choice to change the size of a 2D panel is to reduce the size of the panel bitmap and then move all the gauges to their new locations. Basically starting over.
  8. Hi, This is usually a problem with the...

    Hi,

    This is usually a problem with the static_cg_height line in the Contact Points section of the plane's aircraft.cfg file. This is the height FS places the plane when it loads it and in Slew...
  9. The engine locations are listed in the General...

    The engine locations are listed in the General Engine section of the plane's aircraft.cfg file. You can try editing those. Backup first.
  10. Replies
    6
    Views
    758

    It was America West, but US Airways took it when...

    It was America West, but US Airways took it when they merged.
  11. If all the planes are from the same source then...

    If all the planes are from the same source then they probably all have them in the models. If it is your flyable aircraft too (i.e. all the lights), then you may have installed a halo.bmp...
  12. Thread: Light BMPs

    by tgibson_new
    Replies
    2
    Views
    260

    Are these files within any Program Files folder?

    Are these files within any Program Files folder?
  13. Replies
    4
    Views
    328

    That's true, sometimes custom animations will not...

    That's true, sometimes custom animations will not appear in multiplayer as well.
  14. AFAIK, those are in the model (MDL) file and I...

    AFAIK, those are in the model (MDL) file and I don't know how you change those except by editing the model.
  15. Replies
    4
    Views
    328

    I've seen this before. Sometimes it's because...

    I've seen this before. Sometimes it's because one of you entered multiplayer in slew mode, or you were using a plane with fixed gear and then switched aircraft, or elevation differences as described...
  16. If you set the AI slider to 0, does this fix it? ...

    If you set the AI slider to 0, does this fix it? If so, it's probably a bad texture on one of the AI planes.
  17. Replies
    9
    Views
    1,032

    Try unchecking the Avtive box for this airport's...

    Try unchecking the Avtive box for this airport's scenery in the Scenery Library, restart FS, and try the approach again. If you don't get the crash, the addon scenery is probably the problem.
  18. Replies
    1
    Views
    232

    Hi, According to the TTools documentation, the...

    Hi,

    According to the TTools documentation, the AC# number must be less than 65536. It does not mention if there is a lower limit on the actual number of lines in the file. I have 876 aircraft in...
  19. In the fs9.cfg file is a line starting with: ...

    In the fs9.cfg file is a line starting with:

    SITUATION=

    and some stuff after the equals sign. Quit FS and remove all of that so it looks like the line above. Save and restart FS.

    This...
  20. Replies
    6
    Views
    726

    I assume you downloaded the entire plane,...

    I assume you downloaded the entire plane, including model folders?

    If so, when you loaded the plane into FS did FS ask if it could remove incompatible items? If you said yes, it may have deleted...
  21. Replies
    11
    Views
    1,401

    Sorry that didn't work, I had never tried it for...

    Sorry that didn't work, I had never tried it for that (I use it to flatten the ground under the runway).

    You could create your own ground polygon with a texture of the kind of runway you want. ...
  22. Replies
    11
    Views
    1,401

    If Tim didn't make it clear, you slide the...

    If Tim didn't make it clear, you slide the concrete apron underneath the runway, so it's completely covered by the runway.
  23. Replies
    8
    Views
    929

    Thanks, glad to help. I agree that a video card...

    Thanks, glad to help. I agree that a video card may help, but you can try it with the integrated graphics first and then add the video card when you have more money.
  24. Replies
    8
    Views
    929

    Obviously for $150 you aren't going to get a...

    Obviously for $150 you aren't going to get a screamer, but you can get a box that runs FS9 reasonably. I would get at least an i5 processor and a reasonable graphics system. At that price you won't...
  25. Replies
    14
    Views
    1,245

    Have you set your FS weather settings to the max...

    Have you set your FS weather settings to the max (or as specified in the ASE manual)?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4